DEWALT D21009 Heavy-Duty 6 Amp 3/8-Inch Drill with All Metal Keyless Chuck

List Price: $112.64 Discount Price: $59.95

Features:

• 3/8-inch drill with a powerful 6 amp motor
• 2-sleeve design lets you tighten down on bits with up to 15% more force
• All-metal chuck and front sleeve; all ball-bearing construction; glass-filled nylon housing is durable and impact-resistant
• Built-in 2-way level for drilling accurate vertical and horizontal holes
• Tool weighs 3.5 pounds; 3-year limited warranty

Accessories:
DeWALT Men's Stabilizer Lightweight Oxford	DeWALT Men's Equalizer Composite Toe Hiker	DeWALT Men's 2 X 6 II 6" Steel Toe Work Boot

Customer Reviews:

Poor choice [Posted on 2004-06-14]
I purchased about a year ago and saved $20. It doesnt work,couldnt get it repaired for less than $40, so I gave it to a friend as a paperweight and am in the process of buying another Brand with a decent warrantee like I should have done to begin with. Any Questions?

The DeWalt 21009 is not a heavy duty quality drill. [Posted on 2004-07-08]
I thought it was time to upgrade from the 25 year old 3/8" key chuck Skil brand drill, so I wanted a good, basic, no frills keyless chuck drill when I chose the DeWalt 21009. I made a poor choice in two regards: the keyless chuck loosens while drilling, too often, and will also tighten up on it's own other times to the point I had to use an adjustable wrench to unlock it. Frustrating.

But worse than that, this drill didn't make it through even 6 months of very intermittent use before the motor overheated and is now incapable of drilling a hole of any substance before it grinds to a halt.

I had another DeWalt unit- a DW272 drywall screw driver quit holding bits the very same day. I am now a very disappointed DeWalt customer who will not be buying or recommending DeWalt to anyone. Very frustrating and extremely disappointing.

Luckily I kept the Skil drill and put it back in service.

Awful design: pick another one [Posted on 2005-07-02]
Up 'till now, I've always been impressed with DeWalt (price and quality), but this drill . . . is a different story. The chuck on this needs a major redesign; it's almost impossible to get it tight enough. If you're drilling metal, or using round shaft bits, DO NOT BUY THIS DRILL. It works fine as a screw driver (and with other hex shaped bits), however drilling 1/8" pilot holes in 14ga sheet metal: bad idea. The chuck just slips on the drill bit. I'd recommend any other DeWalt drill, as long as it's got a standard keyed chuck.

Someone at Dewalt Should be Punished... [Posted on 2007-03-17]
... for the horrible no name unusable keyless chuck on this drill. You MUST wear gloves to get a grip on it. No way to get a bit out if the drill is unplugged. Just got a refurb Hitachi D10vhr drill on Amazon that smokes this drill in every category.

Does all right, but - [Posted on 2007-10-15]
I've had this drill for 2 1/2 years, and I use it extensively. After about 10 months, the switch broke, but still under warranty, and was fixed in a couple weeks. Now the chuck is getting hard to loosen and tighten.
There's a drill bit size - roughly 1/8" - that gets stuck in the chuck, and it takes about 30 seconds of giggling with it to get it out.
The chuck also loosens up while you're using it. I've dropped many bits on the floor - and other places.
On the plus side; the drill is fast, light, and strong. I've used it to drive 3" screws over and over again. I've used it with a 4" hole saw (not that I'd recommend doing that). It performs - despite it's flaws.

Click here for more details and discount information...